A few MIG welders advices: how to become a better welder and how to choose the best welding equipment. Never forget that welding, when done improperly, can be hazardous. Electric shock, fumes and gases, arc rays, hot parts, noise and a host of other possible hazards come along with the territory. The ultraviolet and infrared light rays can also burn your skin — similar to a sunburn but without the subsequent tan — and your eyes. This is why the best MIG welding operator knows how to stay safe. Following some simple tips can help you take your MIG welding operation to the next level and ensure you are as safe, efficient and professional as any other shop. Welding helmets, gloves, close-toed shoes and clothes that fully cover exposed skin are essential. Make sure you wear flame-resistant natural fibers such as denim and leather, and avoid synthetic materials that will melt when struck by spatter, potentially causing burns. Also, avoid wearing pants with cuffs or shirts with pockets, as these can catch sparks and lead to injuries.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
Some tips about welding equipment, MIG and TIG welders, plasma cutters. Stick Welding – If you learned to weld years ago, you likely learned using an arc welder. Stick welding for many years has been the most popular method for most home-shop welding needs. This process uses an electric current flowing from a gap between the metal and the welding stick, also known as an arc-welding electrode. Stick welding is an effective method for welding most alloys or joints and can be used indoors and outdoors or in drafty areas. It’s also the most economical welding method and provides the ability to create an effective bond on rusty or dirty metals. However, this method is limited to metals no thinner than 18-gauge, requires frequent rod changing, emits significant spatter and requires that welds be cleaned upon completion. Stick welding is also more difficult to learn and use, particularly the ability to strike and maintain an arc. Arc welders are available in AC, DC or AC/DC, with AC being the most economical. It’s used for welding thicker metals of 1/16 inch or greater. These machines are a good choice for farmers, hobbyists and home maintenance chores.
The welding setup, welder settings, and electrode selection will impact how fast welders can work. Industrial welders invest time in planning the size and shape of their welding areas, how parts are laid out, and how they supply their shielding gas. Testing settings or an electrode on a piece of scrap metal, especially for a beginners, will save time in the long run. Learn more about setting up an efficient shop here. Welding Downhill Increases Welding Speed: While welding downhill is a faster way to weld, it’s not as strong as welding uphill. On most projects it’s not worth sacrificing strength and durability for the sake of welding speed. However, if the metal is thin enough, then welding downhill won’t make the weld weaker and may even be the correct technique for the job. Learn about uphill and downhill welding and see these diagrams of vertical and downhill welding. Read extra details at MIG welder.
Put a glove, block of wood, folded up heat resistant cloth or something non-conductive on the welding table to rest your arms or elbows on and to protect your arms from shock hazard: Do you enjoy getting shocked? Me neither . tig welding aluminum with your high frequency switched to continuous means that the high freq is always looking for a path to follow. So even resting your forearm on the metal table can let that high frequency current bite you just when you least want it, like right when you are near and edge and you are being extra careful not to melt the edge away and then ZAP!. Who needs that? Put a glove, block of wood, folded up heat resistant cloth or something non-conductive on the welding table to rest your arms or elbows on and to protect your arms from shock hazard. Also do whatever it takes to rest your torch hand on a steady object. Again, a block of wood, a balled up tape ball etc can all be used to give you something to rest your torch hand on.